Error Code 0x80300024 When Installing Windows

When installing any Windows in an operating system gives rise to an error 0x80300024. It is one of the most challenging problems one will ever face. Moreover, this error code contains the error message “Windows is unable to install in the selected location”. Therefore it acts as a barrier or hindrance while installing a Window in an operating system.

Moreover, the error code 0x80300024 specifies some of the issues like software or hardware relating to the hard disk partition, which is the destination of the Windows installation. There are various reasons present for the occurrence of the error code 0x80300024.

Error Code 0x80300024 When Installing Windows 10, 8 and 7

They include the insufficient disk space on destination drive or damaged/corrupted installation media to be a damaged, dying or otherwise corrupted hard drive, etc. So these were the reasons that cause this error.

How to Fix Error Code 0x80300024 When Installing Windows

To fix these errors, there are various solutions mention below along with the steps that can solve the problem and prevent it from occurring again. Therefore if this problem occurs in your system do follow the steps mention below to fix the Error Code 0x80300024.

Additional Guides:

Method 1: Remove Any Unnecessary Hard Drives

When the system is connected to more than one hard drive and in one of those hard drives, the installation is being processed then the other drive may act as interference while installing Windows. Therefore an error code 0x80300024 will be shown on the screen after causing the installation failure.

To solve this problem one should follow the steps given below:

Step 1 – Firstly remove the hard drive which is not used while installing the Window from the system.

Step 2 – After that, try the whole installation process again and check whether the issue persists or not.

After following the above steps if the issue is still not resolved then the problem is not caused by the hard drive. Meanwhile, try other methods to resolve the problem that occurs while installing Windows.

Method 2: Try Plugging the Installation Media into a Different USB Port

However, the Window can be installed through USB along with the appropriate installation media. Most of the user uses this method to install the Window in the system through USB so the problem may be caused because of the USB port under which the installation media is a plugin.

Moreover, if this is the main reason for the problem occurring then try solving it by installing Windows with the USB port along with the installation media and insert it in a different USB port, i.e. switch from the USB 2.0 port to USB 3.0 port or vice versa and check whether the problem is resolved or not.

Method 3: Make Sure the Target Drive is At The Top of The Computer’s Boot Order

Moreover, the main cause of the problem can be the hard drive it is installed onto not being at the top of the computer’s boot order. The computer always tries to boot the operating system on startup, which is configured through the average computer’s BIOS. To solve the problem, you need to ensure that the target hard drive is at the top of the computer’s boot order. And to do that follow the steps mention below:

Step 1 – Firstly start the computer.

Step 2 – Then the first screen that appears on the computer during the boost up contains the instructions that states to press the specific key which is mostly the DELETE F1 OR F2 to enter the computer’s BIOS/setup. To enter the BIOS press the specified key.

Step 3 – Now locate the computer’s boot order/configuration in the BIOS. Mostly the BIO’S boot tab contains the boot order. After that, adjust the boot order to bring the hard drive at the top in which the Windows is installed.

Step 4 – Lastly exit the computer’s BIOS, ensuring that the changes are saved and has been updated.

Solution 4: Format the Installation Location

On the contrary, it is advisable to format the installation location before installing Windows on the computer because in most of the cases it is the cause of the problem and formatting the location can bring an end to it. Therefore resolve the problem error code 0x80300024 issues. Thus formatting an installation location is surely a solution.

In order to do that, here are the following steps:

Step 1 – Firstly install the bootable Windows installation media on the computer and then restart it. And Windows Installation media must be created if it’s not in use or not ready to use.

Step 2 – Now choose to boot the inserted installation media after the starting of the computer. Then configure the computer language, keyboard layout and other preference.

Step 3 – Now click on the Custom option. And when it’s asking about the location of the Windows to be installed in, then first click on Drive option (advanced).

Step 4 – After that, click on the partition of the computer’s hard drive, which contains the installed Window. Then select the installed Windows and click on the format option.

Step 5 – Now confirm the action.

Step 6 – Lastly click on the Next after the drive partition is completely formatted to Cary on with the installation.

Solution 5: Replace your Hard Drive

One of the effective methods to solve the error is replacing the hard drive. Its because in most of the cases the hard drive in the computer is dying or is already dead.

A dying hard drive can act as prevention for installing a Window in an operating system. Moreover, its highly recommended to replace the hard drive with the new hard drive. It will surely help you to get rid of the error code 0x80300024 issue.

Conclusion

The methods mentioned above are one of the most excellent ways that are used to solve the error code 0x80300024. It is claimed by the user that the methods are effective and efficient enough to solve the problem. And these methods should definitely bring into use when facing this problem.